环氧地坪为什么老有刷痕?施工初期应该如何保养?

发布日期:2019-07-12 浏览次数:49

环氧地坪刷痕发生的原因:A、施工原因:施工办法过失,涂料拌和后施工时刻过长,滚刷均匀,涂层薄厚控制不到位。B、东西原因:滚筒质量不合格,滚筒外表处理有误。C、涂料自身的原因:主要是涂料的流平性差,涂料的粘度过高。有触变性的填料或助剂。

Reasons for brush marks on epoxy floors: A. Construction reasons: negligence of construction methods, too long construction time after mixing of coatings, even rolling brushing, and inadequate control of coating thickness. B. Eastern and Western Reasons: The quality of the drum is not up to standard, and the surface treatment of the drum is wrong. C. The reason of the coating itself is that the leveling of the coating is poor and the viscosity of the coating is too high. Thixotropic fillers or additives.

环氧地坪刷痕处理的办法:A、留心施工办法,涂料的熟化时刻不要过长。滚筒的二端到圆角,涂层的一遍厚度尽可能不要小于0.15mm。B、买好一点的滚筒,滚筒运用前用胶带处理一下滚筒外表。C、涂料的原因,增加涂料的流平性,下降涂料的粘度,尽可能减稀有触变性的填料和助剂地坪,为什么环氧地坪老有刷痕?特别要留心墙面涂料的流平剂用在地坪涂料的现象。

Epoxy floor brush mark treatment methods: A, pay attention to construction methods, paint maturation time should not be too long. From the two ends of the drum to the fillet, the thickness of the coating should not be less than 0.15mm. B. Buy a better drum. Use tape to deal with the appearance of the drum before it is used. C. Reasons for coatings, increase the levelness of coatings, reduce the viscosity of coatings, as far as possible reduce rare thixotropic fillers and additives floors, why do epoxy floors always have brush marks? Special attention should be paid to the phenomenon that leveling agents of wall coatings are used in floor coatings.

环氧地坪刷痕解决办法:1、避免巩固、尖利的物品直接抵触地上。2、关于溅落到地上上的腐蚀性的化学药品和溶剂应立即铲除。3、环氧地坪关于洒落在地上上的油脂须马上铲除,否则会使地上变滑,易构成损害。4、巩固的重物有必要轻放;5、机器操作台的地上、较重的原材料、半制品或制品存放区地上,铺上一块橡胶垫或软质塑胶垫。6、环氧地坪只能耐受80℃的温度,所以,针对常常需求电焊或氧割的区域,应在地上上铺设钢板或其它耐高温阻隔垫。7、各类推车或拖车的脚轮有必要选用受力面较宽、具有必定弹性的高耐磨聚氨酯脚轮。

Solutions to brush marks on epoxy floor: 1. Avoid consolidation and sharp objects directly touching the ground. 2. Corrosive chemicals and solvents splashed on the ground should be eliminated immediately. 3. Oil and grease sprayed on the ground should be removed immediately from the epoxy floor, otherwise the ground will become slippery and easy to cause damage. 4. It is necessary to lighten the consolidated weight. 5. A rubber pad or soft plastic pad should be laid on the floor of the machine operating platform, on the floor of the heavier raw materials, semi-products or products storage area. 6. Epoxy flooring can only withstand the temperature of 80 C. Therefore, steel plates or other high temperature resistant barrier pads should be laid on the ground for areas where welding or oxygen cutting are often required. 7. It is necessary to choose the high wear-resistant polyurethane casters with wide stress surface and certain elasticity for the casters of all kinds of carts or trailers. 

辛苦整理!转载请注明来自 http://www.pengs888.com/show.asp?id=212
在线咨询
微信咨询
联系电话
13771445261
返回顶部